Socket axle set with closed groove ball bearings (Ø 29 mm) for front cast hubs (Leleu) on your Puch moped / moped.
The threaded shaft set consists of a 165 mm long wheel axle, two special ball bearings and all required nuts and spacers.
The wheel axle set works with Leleu front wheel hubs, which are installed in cast rims.
The cable ties show you where to mount what:
- Red marking: wheel hub
- Green marking: Brake anchor plate
- Yellow marking: Replacement disk for the speedometer drive (the disk is omitted if a drive is fitted)
- Blue marking: fork leg
Note: When installing the ball bearings, it is important to note that the long spacer bushing must be clamped between the two ball bearings to ensure that the two bearings press against the bushing with the inner ring. If this is not observed, the ball bearings will inevitably jam.
| Ø outside | 29.02 mm |
| Ø inside | 12 mm |
| Thread type | MF12x1 (fine pitch thread) |
| Manufacturer | swiing® ingenious parts |
| Thread length | 50 mm, 40.5 mm |
| Ø shaft | 11.95 mm |
| Material | Steel |
| Surface | galvanized (blue) |
| Width | 34.5 mm, 6.6 mm, 11 mm, 2.7 mm |
| Width across flats | 19 mm |
| Shank length | 74.5 mm |
| Height | 9.9 mm, 5.9 mm |
| Total length | 165 mm |
| Ball bearing closed | Yes |
| Puch |
Accessories & related products
Hot 
swiing® ingenious wheel axle with bearing conversion kit spoke hub front | Puch
Ø inside: 12 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Ø outside: 29.02 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Width across flats: 19 mm · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Total length: 165 mm · Ball bearing closed: Yes · Thread length: 40.5 mm · Thread length: 50 mm
EUR 45,80
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Manufacturer: swiing® ingenious parts · Diameter: 29 mm · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 29 mm · Total length: 190 mm · Width across flats: 19 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 29 mm · Thread length: 53 mm · Ø shaft: 19 mm · Shank length: 100 mm · Ball bearing closed: Yes
EUR 45,80
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Width: 9 mm · Ø outside: 29.02 mm · Inner ring width: 9 mm · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: Sheet steel cage ball-guided · Material: Plastic · Material: Steel · Ball bearing closed: Yes
EUR 10,50
GPO speedo drive 17" with lugs 12 mm axle | Puch Maxi S / N, X30 Sport NS / NL, NG-2AH, X30 Velux
Ø outside: 41 mm · Manufacturer: GPO · Ø axle: 12 mm · Material: Aluminum · Place of use: left · Place of use: right · Thread type: MF10x1 (fine pitch thread) · Wheel size: 17 " · 4-edge speedometer cable: 1.8 mm · 4-edge speedometer cable: 2.6 mm · Ø mounting hole: 12 mm
EUR 32,80
Explore categories from Hub & axle
Moped fans also bought
NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi
Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Stock number: 6001 · Width: 8 mm · Ø outside: 28 mm · Inner ring width: 12 mm · Manufacturer: NTN · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Area of application: Standard · Ball bearing closed: Yes
EUR 6,95
Hot
swiing® revival wheel axle LELEU & Grimeca wheel hub cast wheel rear | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 11.8 mm · Total length: 185 mm · Thread length: 26 mm · Thread length: 52.5 mm · Ø shaft: 11.9 mm · Width across flats: 19 mm · Thread type: MF12x1 (fine pitch thread) · Shank length: 100 mm
EUR 17,50
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Manufacturer: swiing® ingenious parts · Diameter: 29 mm · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 29 mm · Total length: 190 mm · Width across flats: 19 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 29 mm · Thread length: 53 mm · Ø shaft: 19 mm · Shank length: 100 mm · Ball bearing closed: Yes
EUR 45,80
Hot
Inner cable set automatic | Puch E50
Manufacturer: Made in Germany · Material: Steel · Quantity: 4 pcs · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears · Total length: 1600 mm · Total length: 2200 mm
EUR 11,70
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 28 mm · Ø outside: 29 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ball bearing closed: Yes
EUR 36,40
SKF 6001 2RSH Ball bearing 12/28/8
Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Stock number: 6001 · Width: 8 mm · Ø outside: 28 mm · Inner ring width: 8 mm · Manufacturer: SKF · Dust protection type: 2RSH - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: Sheet steel cage ball-guided · Ball bearing closed: Yes
EUR 15,20
Working late? Evening hours on Thursday until 20:00
