Pinasco «Slave» engine case with crankshaft (46 mm stroke / 12 mm KoBo) and double intake suitable for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The Pinasco «Power Casing» engine case is supplied with a specially developed crankshaft, which has a wide cheek for controlling the intake.
On this case, a standard 13 mm Dellorto SHA carburetor can be installed at the rear on the one hand, and any side carburetor with a 24 mm connection on the reed system on the other. The frame may have to be adapted if necessary.
This dual carburetor system can be used to tease the last horsepower out of your racing car.
The following parts are included in the scope of delivery:
- Rear intake flange (connection diameter: 16 mm, Ø inside: 13 mm)
- Side diaphragm system incl. sealing plug for the 13 mm flange if this is not used.
- Mounting material for diaphragm flange (connection diameter: 24 mm, Ø inside: 20 mm)
- Cylinder stud bolt
- Engine housing (Ø for cylinder neck up to 50.7 mm)
- Engine housing screws
- Crankshaft Pinasco Competition with 46 mm stroke and 12 mm piston pin (axe 12)
- Installation instructions in English & Italian
No housing seal is supplied. Sealing compound is used for sealing.
We recommend using the 46 mm Pinasco cylinder kit for this racing gear. In addition, only electronic ignitions can be fitted to this housing.
Installation instructions:
- When using the crankshaft with 46 mm stroke, the housing must be slightly recessed inside so that the connecting rod does not protrude
- The cylinder must be raised by approx. 1.5 mm due to the higher stroke. We recommend checking the crushing edge before commissioning. This should be 0.8 - 1.0 mm.
- If the engine is installed in a Piaggio Ciao frame, some material must be removed from the right-hand side of the housing and cylinder. This process is described in the assembly instructions.
Corresponding add-on parts such as sealant, racing kit, racing ignition etc. can be found in the accessories section.
Quality product from the Italian manufacturer Pinasco.
Details
| Manufacturer | Pinasco |
| Material | Aluminum |
| Crankshaft stroke | 46 mm |
| Ignition type | Electronic |
Suitable for the following models
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
Dell'Orto 19 mm PHBG CS carburetor hand choke
Width: 70 mm · Total length: 82 mm · Height: 124 mm · Manufacturer: Dell'Orto · Material: Aluminum · Area of application: Racing · Area of application: Tuning · Component group Carburetor: Carburetor complete · Color: black · Nominal diameter: 19 mm · Carburetor type: PHBG CS · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Ø fuel hose connection: 5.4 mm · Ø fuel hose connection: 6 mm · Ø without reducing sleeve: 26 mm · Ø Inside entrance: 19 mm · Ø Internal connection: 24 mm · Ø Output inside: 19 mm · Ø Air filter connection: 32 mm · Ø Air filter connection: 60 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Mounting type: Plug connection clamped · Mixed oil connection: Yes · Vacuum connection: Yes · Choke nozzle size: 60 · Camouflaged: No · Nozzle size: 75 · Size of secondary nozzle: 45
EUR 140,80
Malossi racing ignition 12V | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Malossi · Area of application: High End · Area of application: Performance · Area of application: Racing · Material: Steel · Area of application: Tuning · Ø Internal flywheel: 80.5 mm · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Number of fixing points: 2 pcs · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 139.5 mm · Ø cable: 7 mm · Weight: 804 g · Weight: 890 g · Mounting type: Screws
EUR 469,50
SKF 6202 C3 ball bearing 15/35/11
Width: 11 mm · Bearing cage: "-" Sheet steel cage ball-guided · Inner ring width: 11 mm · Manufacturer: SKF · Bearing clearance: C3 · Stock number: 6202 · Bearing type: Deep groove ball bearing · Ø inside: 15 mm · Ø outside: 35 mm · Puch OEM number: 900.4.6202
EUR 11,60
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Manufacturer: Elring · Material: Silicone · Temperature resistance (min.): -60 - 315 °C · Area of application: Chemistry · Contents [ml]: 70 ml · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Color: gray · Gap dimension (max.): 2 mm
EUR 23,40
EUR 334,29/l
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Material: Aluminum · Material: Carbon · Manufacturer: Pinasco · Surface: varnished · Height: 38.7 mm · Ø Internal flywheel: 106 mm · Thread type: MF16x1 (fine pitch thread) · Direction of rotation: right · Thread length: 7.5 mm · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Cone ratio: 1:5 · Weight: 650 g
EUR 246,40
Dell'Orto 13/13 SHA carburetor hand choke | Piaggio Ciao P, SC
Material: Aluminum · Manufacturer: Dell'Orto · Total length: 55 mm · Width: 60 mm · Height: 110 mm · Area of application: Tuning · Component group Carburetor: Carburetor complete · Nominal diameter: 13 mm · Carburetor type: SHA (Piaggio) · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Ø fuel hose connection: 5.2 mm · Ø fuel hose connection: 6 mm · Ø without reducing sleeve: 18 mm · Ø Inside entrance: 13 mm · Ø Internal connection: 16 mm · Ø Output inside: 13 mm · Ø Air filter connection: 50.9 mm · Mixed oil connection: No · Mounting type: Plug connection clamped · Color: black · Vacuum connection: No · Camouflaged: No · Nozzle size: 66
EUR 82,10
Not in stock
Malossi oil seal FPM 15/24/5 A crankshaft | Piaggio Ciao, SI, Bravo, Boxer
Material: FPM / FKM (known as VITON®) · Manufacturer: Malossi · Surface: rubberized · Temperature resistance (min.): -30 - 200 °C · Width: 5 mm · Simmering type: A - With rubberized outer part / one sealing lip. · Place of use: Crankshaft · Ø inside: 15 mm · Ø outside: 24 mm
EUR 16,80
Pinasco 46 mm cylinder kit EVOTEN BIG 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Material: Aluminum · Manufacturer: Pinasco · Surface: varnished · Area of application: Tuning · Displacement: 71 ccm · Nominal diameter: 46 mm · Crankshaft stroke: 43 mm · Ø cylinder neck: 49.9 mm · Ø Outlet outside: 22.5 mm · Ø Outlet outside: 25 mm · Ø Outlet outside: 28 mm · Ø outlet inside: 18.5 mm · Ø outlet inside: 20.9 mm · Ø outlet inside: 24.4 mm · Ø piston pin (B): 12 mm · Number of fixing points: 3 pcs · Hole spacing outlet: 47.5 mm · Outlet type: clamped · Outlet type: slanted · Thread outlet: M6x1 (standard thread) · Hole pattern [mm]: 55 x 34 · Decompressor: Yes · Camouflaged: No
EUR 493,00
Pinasco 46 mm cylinder kit EVOTEN 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Material: Aluminum · Manufacturer: Pinasco · Surface: varnished · Area of application: Tuning · Displacement: 71 ccm · Nominal diameter: 46 mm · Crankshaft stroke: 43 mm · Ø cylinder neck: 50 mm · Ø Outlet outside: 22.5 mm · Ø outlet inside: 18.5 mm · Ø piston pin (B): 12 mm · Number of fixing points: 3 pcs · Hole spacing outlet: 48 mm · Outlet type: clamped · Outlet type: slanted · Thread outlet: M6x1 (standard thread) · Hole pattern [mm]: 55 x 34 · Decompressor: Yes · Camouflaged: No
EUR 446,00
Collection only possible with online purchase and appointment.
