Pinasco «EVOTEN BIG BORE» cylinder with 46 mm bore and 71 cc for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The completely reworked 46 mm cylinder from Pinasco is now supplied with a 6-channel layout and the 5-fold bolted cylinder head manufactured for the highest loads.Various racing exhausts can be fitted to the supplied exhaust flange with 22.5 mm outer connection diameter.
The cylinder head is fitted without gasket. For optimum sealing, the tightening torque of 10 Nm for the M6 bolts and 14 Nm for the M7 stud bolts must therefore be observed.
The following parts are included in the scope of delivery:
- Additional screws for the cylinder head
- Decompressor valve (actuation not included)
- Cylinder head empty
- Cylinder and accessories
- Piston with L-ring, rectangular ring and Ø 12 mm piston pin (axe 12)
- Various gaskets for the cylinder base
- Installation instructions in Italian
High-quality cast aluminum and durable Nikasil coating are the hallmarks of this high-end tuning cylinder.
The cylinder kit develops maximum power in the mid to upper rev range. We recommend using the racing cylinder in combination with a variomatic drive.
Mounting on an original engine housing is only possible with major modifications. The cylinder kit can be mounted on the well-known Pinasco, Polini and Malossi racing cases without any adaptation work.
Note: If the cylinder kit is mounted on a Piaggio Ciao, it must be ground down on the cooling fins on the right-hand side. Due to the cut-out for the Ciao's cable duct, the hook on the head for the decompression cable is also missing. As a result, the cylinder cover is only suitable to a limited extent for Piaggio Si, Bravo of the newer generations or Grillo. This can be remedied by attaching the decompression cable to the cylinder head from the front, as on the Ciao or Boxer.
Corresponding add-on parts such as racing gearboxes, racing crankshaft, racing variator etc. can be found in the accessories section.
Quality product from the Italian manufacturer Pinasco.
Details
| Manufacturer | Pinasco |
| Material | Aluminum |
| Surface | varnished |
| Displacement | 71 ccm |
| Area of application | Tuning |
| Crankshaft stroke | 43 mm |
| Nominal diameter | 46 mm |
| Ø cylinder neck | 50 mm |
| Ø Outlet outside | 22.5 mm |
| Number of fixing points | 3 pcs |
| Ø outlet inside | 18.5 mm |
| Ø piston pin (B) | 12 mm |
| Hole spacing outlet | 48 mm |
| Outlet type | slanted, clamped |
| Thread outlet | M6x1 (standard thread) |
| Hole pattern [mm] | 55 x 34 |
| Decompressor | Yes |
| Camouflaged | No |
Suitable for the following models
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
Polini Speed Engine electronic ignition housing | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Color: silver · Crankshaft stroke: 43 mm · Ignition type: Electronic · Stock number: 6202 · Total length: 215 mm · Width: 175 mm · Height: 104 mm
EUR 246,40
Pinasco crankshaft "Racing" 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Pinasco · Material: Steel · Cheek type: standard · Crankshaft stroke: 43 mm · Ø coupling pin / vario pin: 12 mm · Connecting rod length center-center: 87 mm · Total length crankpin ignition side: 91.5 mm · Total length crankpin ignition side: 105 mm · Ø crank webs: 69.7 mm · Ø piston pin (B): 12 mm · Ø Connecting rod eye: 15 mm · Bearing seat right: 15 mm · Ø Bearing seat (ignition side): 15 mm · Thread type: M8x1.25 (standard thread) · Thread length: 13.5 mm · Dimension needle bearing: 12 / 15 x 14.7 mm (axe 12) · Wide crank webs: 32.5 mm · Length 1st paragraph: 21 mm · Length 2nd paragraph: 44 mm · Length 3rd paragraph: 63 mm · Ø 1st step (on the coupling side): 15 mm · Ø 2nd shoulder (on the clutch side): 14.4 mm · Ø 3rd step (on the clutch side): 12 mm · Inlet control time: 146 ° · Control time before O.T: 88 ° · Control time according to O.T: 58 ° · Weight: 712 g · Number of gears: 1 pcs · Area of application: Racing
EUR 275,80
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Material: Aluminum · Material: Carbon · Manufacturer: Pinasco · Surface: varnished · Height: 38.7 mm · Ø Internal flywheel: 106 mm · Thread type: MF16x1 (fine pitch thread) · Direction of rotation: right · Thread length: 7.5 mm · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Cone ratio: 1:5 · Weight: 650 g
EUR 246,40
swiing® revival stud bolt set M7x120 mm cylinder | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Drive: External hexagon · Thread type: M7x1 (standard thread) · Total length: 120 mm · Width across flats SW: 11 mm · Diameter: 6.2 mm · Thread length: 25 mm · Strength class: 8 · Strength class: 8.8
EUR 13,70
swiing® ingenious stud bolt M7x120 / Ø 7.3 shank - 10.9 strength
Manufacturer: swiing® ingenious parts · Material: Steel · Diameter: 7.3 mm · Surface: galvanized (blue) · Thread length: 20 mm · Thread length: 30 mm · Total length: 120 mm · Thread type: M7x1 (standard thread) · Strength class: 10.9
EUR 5,75
Moped fans like you also bought:
Dell'Orto 16 mm PHBG AS carburetor hand choke
Manufacturer: Dell'Orto · Component group Carburetor: Carburetor complete · Carburetor type: PHBG AS · Nominal diameter: 16 mm · Ø Internal connection: 24 mm · Ø without reducing sleeve: 26 mm · Ø Air filter connection: 32 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Ø fuel hose connection: 6 mm · Choke control: Hand choke · Choke nozzle size: 60 · Nozzle thread: M5x0.8 (standard thread) · Nozzle size: 74 · Size of secondary nozzle: 50 · Mounting type: Plug connection clamped · Width: 75 mm · Height: 125 mm · Area of application: Tuning
EUR 152,50
swiing® ingenious 16 mm SHA intake manifold Speed Engine (Version 2.0) | Piaggio Ciao, SI, Bravo
Manufacturer: swiing® ingenious parts · Camouflaged: No · Material: Aluminum · Surface: anodized · Color: graphite colors · Ø inside: 16 mm · Ø External connection: 19 mm · Mounting type: Screws · Hole spacing inlet: 36 mm · Number of fixing points: 2 pcs · Total height: 24.2 mm · Total length: 29 mm · Area of application: Tuning
EUR 38,60
Hot 
Malossi Fly Clutch converter Vario Ø 102 mm | Piaggio SI, Bravo, Boxer
Manufacturer: Malossi · Material: Steel · Number of jaws: 3 pcs · Number of springs: 3 pcs · Angle pulley: 15 ° · Gearbox type: Vario · Ø outside: 102 mm · Hardness level Counter pressure spring: Level 2 (35 kg - yellow / blue / black) · Weight: 1170 g
EUR 234,70
Polini EVO Electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Polini · Ø Internal flywheel: 80.5 mm · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Number of fixing points: 2 pcs · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 138.5 mm · Area of application: High End · Area of application: Racing · Area of application: Tuning · Weight: 554 g
EUR 586,90
Collection only possible with online purchase and appointment.
