
Gearwheel of the primary drive for 2-speed manual Z50 engines of Puch X30 NS, NL mopeds / mopeds.
This drive wheel is used in combination with clutch pistons, which have 19 teeth.
Number of teeth: 69
Toothing: helical
Mounting: 3-prong profile
Note: There may be a slight singing after installation until the tooth flanks are ground in cleanly on the clutch basket.
The fastening nut and other parts can be found under accessories.
Original Puch spare part number: 349.3.13.200.1
| Manufacturer | HS-Retro |
| Material | Steel |
| Toothing type | helical toothed |
| Number of teeth | 69 pcs |
| Ø inside | 12.5 mm |
| Ø outside | 95 mm |
| Recording type | 3-tooth splined shaft holder |
| Puch OEM number | 349.3.13.200.1 |
| Puch | Z50 (X30 Sport) |
Accessories & related products
Normio M10x1 Galvanized Nut
Manufacturer: Normio · Material: Steel · Surface: galvanized (blue) · Nut type: Hexagon nut · Thread type: MF10x1 (fine pitch thread) · Nominal diameter (thread): 10 mm · Drive: External hexagon · Height: 8 mm · Width across flats: 17 mm · Tomos OEM number: 215487
EUR 3,40
HS-Retro bearing ring 24/32/7.5 large Z50 (1A quality) | Puch X30 NS, NL
Manufacturer: HS-Retro · Width: 7.55 mm · Material: Steel · Surface: hardened & ground · Area of application: High End · Area of application: Original · Ø outside: 31.98 mm · Ø inside: 23.8 mm · Puch OEM number: 329.1.13.065.1
EUR 69,30
HS-Retro bearing race 19.4/28.1/7.5 small Z50 (1A quality) | Puch X30 NS, NL
Manufacturer: HS-Retro · Width: 7.5 mm · Material: Steel · Surface: hardened & ground · Area of application: High End · Area of application: Original · Ø outside: 28.1 mm · Ø inside: 19.44 mm · Puch OEM number: 329.1.13.010.1
EUR 52,80
HS-Retro clutch basket 19 teeth 2-plate version | Puch Z50
Manufacturer: HS-Retro · Material: Steel · Area of application: High End · Area of application: Original · Toothing type: helical toothed · Ø outside: 74.8 mm · Ø inside: 17 mm · Number of teeth: 19 pcs · Height: 26.6 mm · Puch OEM number: 350.1.12.002.2
EUR 188,20
Explore categories from Gearbox & housing (motor)
Moped fans also bought
GPO license plate holder Inox (CH version)
Manufacturer: GPO · Material: Chrome steel (colloquially known as stainless steel) · Color: silver · Thread type: M5x0.8 (standard thread) · Number of fixing points: 2 pcs · Width: 105 mm · Mounting type: Nuts & bolts · Height: 5.3 mm · Total length: 145 mm · Ø mounting hole: 5 mm · Hole spacing: 30 mm · Hole spacing: 50 mm · Thread length: 8 mm
EUR 12,80
Airsal 46 mm cylinder kit straight exhaust | Puch
Manufacturer: Airsal · Material: Aluminum · Camouflaged: No · Surface: sandblasted · Area of application: Tuning · Crankshaft stroke: 43 mm · Ø piston pin (B): 12 mm · Nominal diameter: 46 mm · Thread inlet: M6x1 (standard thread) · Hole spacing outlet: 42 mm · Number of fixing points: 4 pcs · Outlet type: straight · Hole spacing inlet: 38 mm · Thread outlet: M6x1 (standard thread) · Hole pattern [mm]: 44 x 44
EUR 205,80
Surflex clutch plate set | Puch Z50
Manufacturer: Surflex · Material: Composite materials · Material: Steel · Area of application: Original · Ø outside: 69.6 mm · Ø outside: 74.8 mm · Ø inside: 46.3 mm · Ø inside: 51.3 mm · Recording type: Interlocking · Number of slats: 2 pcs · Thickness: 2.75 mm
EUR 41,10
swiing® ingenious clutch spring reinforced +40% | Puch Z50
Spring design: Pressure spring · Ø wire: 4.5 mm · Total length: 23.5 mm · Manufacturer: swiing® ingenious parts · Number of components: 1 pcs · Surface: coated · Area of application: Tuning · Ø outside: 39 mm · Material: Spring steel · Ø inside: 30 mm · Color: red
EUR 28,10
HS-Retro clutch basket 19 teeth 2-plate version | Puch Z50
Manufacturer: HS-Retro · Material: Steel · Area of application: High End · Area of application: Original · Toothing type: helical toothed · Ø outside: 74.8 mm · Ø inside: 17 mm · Number of teeth: 19 pcs · Height: 26.6 mm · Puch OEM number: 350.1.12.002.2
EUR 188,20









