Hot 
High-quality ADDY 4-bearing engine housing, which forms the engine block for a Puch moped with an E50 engine.
New features include a kickstand mount, milled (rather than cast) overflow channels, and a shallower cast recess for GME systems, allowing the housing to be bored out to accommodate large cylinders with a bore diameter of up to 58 mm. Furthermore, the serial number has been repositioned so that it is now located on the right side. This allows you to stamp the frame number into the top surface as needed.
The housing was specifically designed and manufactured for the tuning sector; therefore, some components—such as the mounting surface for a kickstarter—have been omitted.
The housing features the following special characteristics:
- Enlarged sealing surface in the area of the cylinder base
- Casing screws slightly offset outward, leaving more space for larger overflow channels
- Pre-milled surface for GME intake systems
- Locating pins for secure positioning when assembling the housing halves
- Additional threads for more flexible ignition installation
- Extra-large cooling fins in the lower section for better heat dissipation and thus reduced wear on the crankshaft bearings
- Stand mount, 3 M6 threads at the original spacing
- Approved for all SAM moped racing and moped cross categories
- Cylinder stud hole pattern: 44 x 44 mm
- Cylinder neck diameter: 48.4 mm (can be reamed up to 58.0 mm if no GME is installed)
Installation tips:
- When installing original intake components and an SRE carburetor, a 2 mm-thick intake gasket must be used to ensure the float chamber does not rest on the GME block.
- Using the included washers, various gear wheels with different positions—such as those found in 3-bearing or MBR transmissions—can be properly spaced. Be sure to check that the gear wheel is properly centered before reassembly!
- Use the following screw lengths: 7 pcs. M6 x 35 mm / 6 pcs. M6 x 50 mm
Note: If you plan to use a center stand, we recommend using a sturdy center stand, as there is a stand stop only on the left side.
A quality product from the ADDY by Schöb Engineering brand.
Alternative to the original Puch part number: 349.3.10.332.0
| Manufacturer | ADDY |
| Material | Aluminum |
| Alternative version of the Puch OEM number | 349.3.10.332.0 |
| Puch | E50 |
Accessories & related products
GPO Gasket Set for E50 Engine | Puch Maxi S, N
Manufacturer: GPO · Material: Aluminum · Material: Fiber · Material: Sealing carton · Material: Sealing paper · Ø outlet inside: 19.9 mm · Area of application: Standard · Hole spacing inlet: 32 - 38 mm · Hole spacing outlet: 42 mm · Number of components: 7 pcs · Hole pattern [mm]: 44 x 44 · Decompressor: Yes
EUR 11,70
swiing® revival crankshaft "original" | Puch E50
Manufacturer: swiing® revival parts · Material: Steel · Cheek type: standard · Crankshaft stroke: 43 mm · Weight: 873 g · Thread type: MF10x1 (fine pitch thread) · Thread type: MF8x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Area of application: Standard · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
EUR 105,80
Hot
swiing® ingenious crankshaft "High End" with mounted bearings | Puch E50
Manufacturer: swiing® ingenious parts · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Crankshaft stroke: 43 mm · Weight: 968 g · Thread type: MF10x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø piston pin (B): 12 mm · Area of application: High End · Area of application: Racing · Area of application: Tuning · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
EUR 217,60
Not in stock
Explore categories from Gearbox & housing (motor)
Moped fans also bought
swiing® revival oil filler plug with sealing ring | Puch E50
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Nominal diameter (thread): 10 mm · Drive: Slot · Screw head: Lens head · Ø External head: 14 mm · Thread type: M10x1.5 (standard thread) · Total length: 14.6 mm · Thread length: 6 mm · Number of components: 2 pcs · Puch OEM number: 364.1.10.660.1
EUR 4,60
swiing® revival Stud Bolt Set M6x106 | Puch
Diameter: 5.9 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Thread type: M6x1 (standard thread) · Nominal diameter (thread): 6 mm · Drive: External hexagon · Width across flats: 10 mm · Total length: 106 mm · Thread length: 13 mm · Thread length: 18.5 mm · Alternative version of the Puch OEM number: 360.1.10.034.1
EUR 8,70
MBR clutch basket 18 teeth Racing straight | Puch E50
Ø inside: 15 mm · Ø inside: 17 mm · Ø outside: 99.5 mm · Height: 49 mm · Manufacturer: MBR · Material: Steel · Toothing type: straight toothed · Ø Receptacle: 31 mm · Recording type: Interlocking · Number of teeth: 18 pcs · Area of application: Tuning
EUR 217,60
Working late? Evening hours on Thursday until 20:00
