Hot 
Complete set of the 12V swiing® ingenious EVO ignition with built-in 60W light coil and fan wheel. Suitable for your Puch moped / moped with E50 and Z50 engine.
Advantages of the EVO tuning ignition:
- Always a constant, strong spark
- No more misfires
- One-time adjustment
- Little to no wear
- Large adjustment range thanks to long slots
The following special features characterize this ignition:
- From the factory more flywheel mass than HPI ignitions, therefore smoother engine idling (382 grams)
- Fine balanced flywheel for less vibration
- Trigger thread with normal M26x1.5 mm pitch, so normal Bosch/Ducati flywheel pullers can be used
- Easy adjustment of the ignition timing
- The stator was designed for high heat loads;designed for high heat loads, no more failures due to overheating
- Optimized ignition curve (adjustment 12° - 14°)
- Light voltage: 12 Volt
- Light output: 60 Watt
- Ø outside flywheel: 75 mm
- Flywheel cone: ratio 1:5 (standard for Puch & Sachs crankshafts)
- Ø outer stator plate: 90 mm
Installation instructions:
- Right-turning engines: Set piston to TDC, marking on the base plate at 11 o'clock (to the left of the swiing logo) must match the marking on the flywheel, this achieves a timing of 2 mm before TDC.
- Left-turning engines: Set the piston to TDC, the marking on the base plate at 13 o'clock (to the right of the swiing logo) must match the marking on the flywheel, thus achieving a timing point of 2 mm before TDC.
- Flywheel tightening torque: 37 - 39 Nm (no keyway available)
- The CDI and ignition coil must be supplied with a good earth (grounding), otherwise they can be damaged within a short time.
- The lighting system should also be equipped with a 12 V voltage regulator.
Correct pinning of the Superseal connector:
- 1 = black
- 2 = blue
- 3 = white
Attention: The ignition components stator, rotor, CDI and ignition coil are not compatible with parts of the HPI ignition!
When you buy this complete set, you get a big discount on the retail price of the individual parts.
The ignition is compatible with cable starters, which also fit the HPI, you can find these in the accessories section.
Exclusive product for the highest demands of the quality brand swiing®.
| Puch | E50 Z50 (X30 Sport) |
Accessories & related products
Nos
Hot
BERU Spark Plug Connector, 1 kΩ, Noise-Suppressed, NOS
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Ø cable: 5 mm · Ø cable: 7 mm · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Subcategory: Spark plug connector · Pony OEM number: A2099 · Sachs OEM no.: 0265 100 00
EUR 11,70
Hot
GPO flywheel trigger M26x1.5 / M22x1.5 | Puch, Sachs, Tomos, Beta 521
Width across flats trigger: 27 mm · Manufacturer: GPO · Clamping depth: 10 mm · Material: Steel · Surface: blackened · Total length: 55 mm · Total length: 75 mm · Area of application: (Dis)assembly tool · Width across flats Screw: 19 mm · Thread type: MF22x1.5 (fine pitch thread) · Thread type: MF26x1.5 (fine pitch thread) · Strength class: 8.8 · Number of components: 1 pcs
EUR 11,70
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Area of application: Chemistry · Color: blue · Contents: 10 ml · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Temperature resistance (min.): -75 - 200 °C · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
EUR 25,80
EUR 2.580,00/l
swiing® ingenious pull starter EVO & HPI ignition (210) | Puch E50
Manufacturer: swiing® ingenious parts · Material: Plastic · Material: Steel · Surface: chrome-plated · Surface: raw · Color: Chrome · Color: black · Ignition system: HPI · Ø outside: 130 mm · Number of fixing points: 2 pcs · Hole spacing: 137.5 mm · Height: 93 mm · Total length: 160 mm · Width: 135 mm
EUR 176,40
Vibration dampener, 8 mm, with M6x10 threads on both sides
Ø outside: 14.7 mm · Total length: 28 mm · Height: 8 mm · Thread type: M6x1 (standard thread) · Manufacturer: Made in Europe · Thread length: 10 mm · Color: black · Material: Rubber · Material: Steel · Nominal diameter (thread): 6 mm
EUR 5,15
DENSO (IWF24 / IWF27) Spark plug short thread U-Groove Iridium
Manufacturer: DENSO · Candle thread type: short · Thread type: MF14x1.25 (fine pitch thread) · Width across flats: 21 mm · Spark plug socket: M4 · Electrode material: Iridium · Suppressed: No · Area of application: Cross · Area of application: High End · Area of application: Tuning
EUR 30,50
Ignition cover high "Puch" (old emblem) chrome | Puch E50 / Z50 / ZA50 (wind cooled)
Manufacturer: FAST ARROW · Material: Steel · Surface: chrome-plated · Color: Chrome · Height: 62 mm · Ø outside: 126 mm · Ø inside: 124 mm · Number of fixing points: 2 pcs · Alternative version of the Puch OEM number: 349.1.10.034.1
EUR 46,90
Moped fans also bought
Nos
Hot
BERU Spark Plug Connector, 1 kΩ, Noise-Suppressed, NOS
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Ø cable: 5 mm · Ø cable: 7 mm · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Subcategory: Spark plug connector · Pony OEM number: A2099 · Sachs OEM no.: 0265 100 00
EUR 11,70
Hot
GPO flywheel trigger M26x1.5 / M22x1.5 | Puch, Sachs, Tomos, Beta 521
Width across flats trigger: 27 mm · Manufacturer: GPO · Clamping depth: 10 mm · Material: Steel · Surface: blackened · Total length: 55 mm · Total length: 75 mm · Area of application: (Dis)assembly tool · Width across flats Screw: 19 mm · Thread type: MF22x1.5 (fine pitch thread) · Thread type: MF26x1.5 (fine pitch thread) · Strength class: 8.8 · Number of components: 1 pcs
EUR 11,70
Hot
swiing® revival side protection screw set black | Puch Maxi S
Manufacturer: swiing® revival parts · Material: Plastic · Material: Steel · Surface: galvanized (blue) · Surface: raw · Color: silver · Drive: Slot · Drive: Triangular head · Total length: 47 mm · Total length: 60 mm · Thread type: M5x0.8 (standard thread) · Thread length: 35 mm · Thread length: 50 mm
EUR 15,20
Hot
swiing® ingenious 15 mm carburetor camouflaged | Puch
Manufacturer: swiing® ingenious parts · Total length: 66 mm · Material: Aluminum · Component group Carburetor: Carburetor complete · Area of application: Tuning · Carburetor type: SRE · Height: 95 mm · Nominal diameter: 15 mm · Ø Internal connection: 20 mm · Width: 50 mm · Ø Inside entrance: 15 mm · Ø Output inside: 15 mm · Mounting type: Plug connection clamped · Ø Air filter connection: 20 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle block: 2.17 · Camouflaged: Yes · Nozzle size: 62 · Clamping screw torque (max.): 4 N/m · Alternative version of the Puch OEM number: 349.1.15.100.0 · Alternative version of the Puch OEM number: 349.2.15.800.0 · Alternative version of the Puch OEM number: 349.4.15.500.0 · Alternative version of the Puch OEM number: 349.4.15.000.0 · Alternative version of the Puch OEM number: 349.4.15.300.0 · Alternative version of the Puch OEM number: 349.6.15.400.0 · Alternative version of the Puch OEM number: 349.7.15.700.0 · Alternative version of the Puch OEM number: 349.8.15.400.0 · Alternative version of the Puch OEM number: 349.9.15.300.0
EUR 94,00
Working late? Evening hours on Thursday until 20:00
