Pinasco «EVOTEN» cylinder with 42 mm bore and 60 cc for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The completely üreworked 42 mm cylinder from Pinasco is now supplied with a 5-channel layout and the 5-fold bolted cylinder head manufactured for the highest loads. Various racing exhausts can be fitted to the supplied exhaust flange with 22.5 mm outer connection diameter.
The cylinder head is fitted without gasket. For optimum sealing, the tightening torque of 10 Nm for the M6 bolts and 14 Nm for the M7 stud bolts must therefore be observed.
The following parts are included in the scope of delivery:
- Additional bolts for the cylinder head
- Decompressor valve (actuation not included)
- Cylinder head empty
- Cylinder and accessories
- Piston with L-ring, rectangular ring and 10 mm piston pin (axe 10)
- Various gaskets for the cylinder base
- Cylinder head with L-ring, rectangular ring and 10 mm piston pin (axe 10)
- Various gaskets for the cylinder base
- Piston with L-ring, rectangular ring and 10 mm piston pin (axe 10);for the cylinder base
- Installation instructions in Italian
High-quality cast aluminum and durable Nikasil coating characterize this high-end tuning cylinder.
The cylinder kit develops maximum power in the mid to upper rev range. We recommend using the racing cylinder in combination with a variomatic drive.
Mounting on an original engine housing is only possible with major modifications. The cylinder kit can be fitted to the well-known Pinasco, Polini and Malossi racing cases without any adaptation work.
Note: If the cylinder kit is fitted to a Piaggio Ciao, this must be ground down on the cooling fins on the right-hand side. Due to the cut-out for the Ciao's cable duct, the hook on the head for the decompression cable is also missing. As a result, the cylinder cover is only suitable to a limited extent for Piaggio Si, Bravo of the newer generations or Grillo. This can be remedied by attaching the decompression cable to the cylinder head from the front, as on the Ciao or Boxer.
Corresponding add-on parts such as racing gearboxes, racing crankshaft, racing variator etc. can be found in the accessories section.
Quality product from the Italian manufacturer Pinasco.
| Nominal diameter | 42 mm |
| Manufacturer | Pinasco |
| Material | Aluminum |
| Surface | varnished |
| Displacement | 60 ccm |
| Area of application | Tuning |
| Crankshaft stroke | 43 mm |
| Number of fixing points | 3 pcs |
| Ø Outlet outside | 22.5 mm |
| Ø piston pin (B) | 10 mm |
| Outlet type | clamped |
| Decompressor | Yes |
| Camouflaged | No |
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
swiing® ingenious needle roller bearing 12/15/16.2 "Racing" silver cage
Bearing cage: Silver cage · Manufacturer: swiing® ingenious parts · Bearing type: Needle roller and cage assembly · Width: 16.2 mm · Ø outside: 15 mm · Ø inside: 12 mm · Dimension needle bearing: 12/15 x 16.2 · Tomos OEM number: 035548
EUR 16,40
Polini Speed Engine electronic ignition housing | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Manufacturer: Polini · Material: Aluminum · Color: silver · Crankshaft stroke: 43 mm · Width: 175 mm · Height: 104 mm · Surface: sandblasted · Total length: 215 mm · Ignition type: Electronic
EUR 247,10
Polini Speed Engine engine case breaker ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Manufacturer: Polini · Material: Aluminum · Color: silver · Crankshaft stroke: 43 mm · Width: 175 mm · Height: 104 mm · Surface: sandblasted · Total length: 215 mm · Ignition type: Breaker
EUR 247,10
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Pinasco · Material: Aluminum · Material: Carbon · Ø Internal flywheel: 106 mm · Thread type: MF16x1 (fine pitch thread) · Direction of rotation: right · Height: 38.7 mm · Surface: varnished · Thread length: 7.5 mm · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Cone ratio: 1:5 · Weight: 650 g
EUR 247,10
swiing® revival stud bolt set M7x120 mm cylinder | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Material: Steel · Diameter: 6.2 mm · Thread type: M7x1 (standard thread) · Drive: External hexagon · Surface: galvanized (blue) · Thread length: 25 mm · Total length: 120 mm · Width across flats SW: 11 mm · Strength class: 8 · Strength class: 8.8
EUR 13,80
swiing® ingenious stud bolt M7x120 / Ø 7.3 shank - 10.9 strength
Manufacturer: swiing® ingenious parts · Material: Steel · Diameter: 7.3 mm · Thread type: M7x1 (standard thread) · Surface: galvanized (blue) · Thread length: 20 mm · Thread length: 30 mm · Total length: 120 mm · Strength class: 10.9
EUR 5,75
Collection only possible with online purchase and appointment.
