Reinforced pull bolt compatible with the manual-shift Z50 engine in the Puch X30 Sport NS / NL, as well as Puch X30 Velux mopeds.
Version with thrust bearing: The thrust bearing alone is designed for extreme loads when used with very strong clutch springs.
However, due to slightly poorer guidance, this bearing may produce slightly more noise than conventional release bearings with a 60° contact angle.
The reinforced clutch springs included in the accessory set can be used without any problems in combination with the clutch bearing.
Clutch adjustment: Figure 4 shows the position of the release lever relative to the abutment and the ball-collar nut relative to the release shaft. This adjustment provides maximum release travel with minimal effort. Particular attention should be paid to the play between the disengagement shaft and the tapered collar nut, as insufficient play will inevitably cause the clutch bearing to fail very quickly. With the clutch cable engaged, the free travel on the disengagement lever should be approximately 3 mm.
The angle “A” shown in the illustration is 58°. At the hand lever, these clearances result in a free travel of approximately 1 cm.
A good, affordable standard replacement part. GPO – GOOD PARTS ONLY.
| Manufacturer | GPO |
| Material | Metal |
| Area of application | Tuning |
| Puch | Z50 (X30 Sport) Z50 (X30 Velux) 2-speed MS, MV, MV50 |
Accessories & related products
swiing® revival clutch spring 2-disc version | Puch Z50
Spring design: Pressure spring · Ø wire: 4 mm · Ø inside: 30.5 mm · Ø outside: 39 mm · Total length: 19.5 mm · Manufacturer: swiing® revival parts · Number of components: 1 pcs · Material: Spring steel · Color: gray · Area of application: Original · Area of application: Standard
EUR 21,10
swiing® ingenious clutch spring reinforced +20% | Puch Z50
Spring design: Pressure spring · Ø wire: 4.6 mm · Ø inside: 30 mm · Ø outside: 39 mm · Total length: 20.5 mm · Color: blue · Manufacturer: swiing® ingenious parts · Number of components: 1 pcs · Material: Spring steel · Surface: coated · Area of application: Tuning
EUR 28,10
swiing® ingenious clutch spring reinforced +40% | Puch Z50
Spring design: Pressure spring · Ø wire: 4.5 mm · Ø inside: 30 mm · Ø outside: 39 mm · Total length: 23.5 mm · Color: red · Manufacturer: swiing® ingenious parts · Number of components: 1 pcs · Material: Spring steel · Surface: coated · Area of application: Tuning
EUR 28,10
Explore categories from Clutch
Moped fans also bought
swiing® revival gearbox cover gasket (old model) | Puch Z50 engine
Manufacturer: swiing® revival parts · Material: Sealing paper · Total length: 166 mm · Color: sand-colored · Number of components: 1 pcs · Width: 155 mm · Thickness: 0.35 mm · Number of fixing points: 8 pcs · Puch OEM number: 349.1.10.249.1
EUR 4,60
Motorex engine oil (gear oil) manual 450 ml
Temperature resistance (min.): -30 - 220 °C · Manufacturer: Motorex · Oil type: GL4 · Viscosity (SAE): 80W · Contents: 450 ml · Gearbox type: Foot control · Gearbox type: Manual gearshift · Area of application: Gearbox lubrication with clutch
EUR 13,50
EUR 30,00/l
swiing® revival engine gasket | Puch Z50 engine X30 NS, NL
Manufacturer: swiing® revival parts · Material: Sealing paper · Color: sand-colored · Number of components: 1 pcs · Total length: 240 mm · Width: 167 mm · Thickness: 0.4 mm · Ø inside: 74 mm · Number of fixing points: 12 pcs · Puch OEM number: 349.1.10.231.1
EUR 6,60
swiing® revival spacer set crankshaft L17 | Puch Z50
Ø inside: 17.1 mm · Nominal diameter inside: 17 mm · Ø outside: 23.8 mm · Thickness: 0.1 mm · Thickness: 0.15 mm · Thickness: 0.2 mm · Thickness: 0.25 mm · Thickness: 0.3 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: blank / oiled
EUR 10,50
Working late? Evening hours on Thursday until 20:00
