41 mm cast iron racing cylinder with Latin American temperament and 57 cc for your Puch M50, MS50, VS50, DS50, VZ50 small motorcycle.
The timing cam of the tuning cylinder was deliberately kept low, which results in particularly good torque in the lower engine speed range.
Thanks to the large sealing surface, no more pouring is required to close the slot on the housing compared to many other cylinder kits.
Compared to the Sombrero racing kit for Puch Velux X30 models, this version has a thinner cylinder neck so that it fits into the corresponding EX50 engine cases.
| Manufacturer | GPO |
| Material | Gray cast iron |
| Camouflaged | No |
| Displacement | 57 ccm |
| Crankshaft stroke | 43 mm |
| Nominal diameter | 41 mm |
| Ø cylinder neck | 43 mm |
| Ø outlet inside | 25 mm |
| Ø Inlet inside | 19 mm |
| Thread inlet | M6x1 (standard thread) |
| Hole spacing outlet | 42 mm |
| Number of fixing points | 4 pcs |
| Hole pattern [mm] | 44 x 44 |
| Ø piston pin (B) | 10 mm, 12 mm |
| Outlet type | straight |
| Thread outlet | M6x1 (standard thread) |
| Decompressor | No |
| Hole spacing inlet | 42 mm |
| Area of application | Tuning |
| Puch | 2-speed MS, MV, MV50 3-speed VSD, DS, VZ, MC |
Accessories & related products
Dirko Dichtmasse rot (Silikon) Hochtemperatur 70 ml dauerelastisc
Manufacturer: Elring · Area of application: Chemistry · Color: red · Contents [ml]: 70 ml · Hazard warning: Causes serious eye irritation · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Gap dimension (max.): 2 mm · Temperature resistance (min.): -60 - 300 °C
EUR 26,80
EUR 382,86/l
GPO cylinder gasket set BAD ASS Lucifer / GPO Sombrero 41 mm | Puch X30 Velux, M50, MS
Manufacturer: GPO · Material: Aluminum · Material: Sealing paper · Number of components: 4 pcs · Thickness: 0.4 mm · Thickness: 0.45 mm · Ø cylinder: 41 mm · Hole spacing inlet: 32 mm · Ø outlet inside: 27 mm · Hole spacing outlet: 32 mm · Hole pattern [mm]: 44 x 44 mm · Decompressor: Yes · Area of application: Tuning
EUR 23,30
GPO Ø 41 mm "Sombrero" cylinder kit | Puch X30 Velux, NG-2AH
Nominal diameter: 41 mm · Manufacturer: GPO · Material: Gray cast iron · Displacement: 57 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 44.7 mm · Ø outlet inside: 25 mm · Ø Inlet inside: 19 mm · Thread inlet: M6x1 (standard thread) · Area of application: Tuning · Hole spacing inlet: 32 mm · Ø piston pin (B): 10 mm · Ø piston pin (B): 12 mm · Outlet type: straight · Hole spacing outlet: 42 mm · Thread outlet: M6x1 (standard thread) · Number of fixing points: 4 pcs · Hole pattern [mm]: 44 x 44 · Decompressor: No · Camouflaged: No
EUR 210,90
EUR 234,30
Moped fans also bought
swiing® ingenious pull starter Bosch / Ducati | Puch E50
Ø outside: 130 mm · Manufacturer: swiing® ingenious parts · Material: Plastic · Material: Steel · Surface: chrome-plated · Color: Chrome · Color: black-matt · Ignition system: BOSCH · Ignition system: DUCATI · Total length: 160 mm · Width: 150 mm · Hole spacing: 137.5 mm · Height: 88 mm · Number of fixing points: 2 pcs
EUR 175,70
GPO piston 41 mm (12 mm KoBo) | Puch X30 Velux, M50, MS50, VS50, DS50, VZ50
Manufacturer: GPO · Nominal diameter: 41 mm · Ø outside piston (A): 40.94 mm · Ø piston pin (B): 12 mm · Compression height (C): 23.2 mm · Curvature (D): 3.7 mm · Total piston height (E): 49.3 mm · Number of piston rings (F): 2 pcs · Piston ring mold: L-ring · Piston ring mold: Rectangular ring · Piston ring impact: Flank safety device (FS) · Piston ring impact: Internal fuse (IS) · Piston weight: 85 g
EUR 58,50
swiing® ingenious wheel axle with bearing conversion kit spoke hub front Ø 29 mm | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 29.02 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width across flats SW: 19 mm · Width: 35.7 mm · Thread type: MF12x1 (fine pitch thread) · Height: 5.9 mm · Height: 9.9 mm · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Thread length: 40.5 mm · Thread length: 50 mm
EUR 45,60
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø shaft: 19 mm · Ø inside: 12 mm · Diameter: 29 mm · Total length: 190 mm · Thread length: 29 mm · Thread length: 53 mm · Ø outside: 29 mm · Width across flats SW: 19 mm · Shank length: 100 mm
EUR 42,00
EUR 45,60
swiing® revival special nut M6 SW8 (sprocket ref. back pedal / intake manifold)
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Nut type: Hexagon nut · Thread type: M6x1 (standard thread) · Height: 6 mm · Drive: External hexagon · Width across flats SW: 8 mm
EUR 3,40
Hot 
swiing® ingenious 17 mm SRF carburetor tuning camouflaged | Puch Maxi, Supermaxi, X30 NS / NL
Manufacturer: swiing® ingenious parts · Camouflaged: Yes · Component group Carburetor: Carburetor complete · Material: Aluminum · Carburetor type: SRE · Nominal diameter: 17 mm · Ø Internal connection: 23 mm · Ø Inside entrance: 17 mm · Ø Output inside: 17.1 mm · Ø Air filter connection: 27.5 mm · Ø fuel hose connection: 5 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle block: 2.2 · Nozzle size: 74 · Mounting type: Plug connection clamped · Clamping screw torque (max.): 3 N/m · Clamping screw torque (max.): 4 N/m · Total length: 65 mm · Width: 47 mm · Height: 89 mm · Height: 109 mm · Area of application: Tuning
EUR 140,60
swiing® revival stud bolt cylinder base M6x26 - 10.9 strength | Sachs
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Diameter: 5.8 mm · Thread type: M6x1 (standard thread) · Total length: 26 mm · Thread length: 9 mm · Thread length: 13 mm · Strength class: 10.9
EUR 2,10
Hot
swiing® ingenious intake manifold 17 mm SRF camouflaged | Puch E50
Manufacturer: swiing® ingenious parts · Camouflaged: Yes · Material: Aluminum · Ø inside: 17 mm · Ø External connection: 23 mm · Mounting type: Stud bolts & nuts · Hole spacing inlet: 38 mm · Number of fixing points: 2 pcs · Total height: 53.5 mm · Height flange center hole: 42 mm · Total length: 38 mm · Area of application: Performance · Area of application: Racing · Area of application: Tuning
EUR 52,60
swiing® ingenious intake manifold 17 mm SRF | Puch Z50
Manufacturer: swiing® ingenious parts · Camouflaged: Yes · Material: Aluminum · Ø inside: 17 mm · Ø External connection: 23 mm · Mounting type: Stud bolts & nuts · Hole spacing inlet: 38 mm · Number of fixing points: 2 pcs · Total height: 73 mm · Height flange center hole: 61 mm · Total length: 45 mm · Area of application: Performance · Area of application: Racing · Area of application: Tuning
EUR 58,50
Collection only possible with online purchase and appointment.
